Cisco devise configuration newbie - switch command Daquan (part one)

Cisco devise configuration newbie - switch command Daquan  (part   one)

You need to read the article if you are preparing for IT certification.

1. Set the host name / system name based on IOS switches:

 

Switch(config)# hostname hostname

 

Set the hostname / system name on the CLI- based switch :

 

Switch(enable) set system name name-string

 

2. Set the login password on the IOS- based switch :

 

Switch(config)# enable password level 1 password

 

Set the login password on the CLI- based switch :

 

Switch(enable) set password

 

Switch(enable) set enalbepass

 

3. Set up remote access on IOS- based switches :

 

Switch(config)# interface vlan 1

 

Switch(config-if)# ip address ip-address netmask

 

Switch(config-if)# ip default-gateway ip-address

 

Set up remote access on a CLI- based switch :

 

Switch(enable) set interface sc0 ip-address netmask broadcast-address

 

Switch(enable) set interface sc0 vlan

 

Switch(enable) set ip route default gateway

4. Enable and browse CDP information on IOS- based switches :

 

Switch(config-if)# cdp enable

 

Switch(config-if)# no cdp enable

 

In order to view the CDP notification information of Cisco neighboring devices :

 

Switch# show cdp interface [type modle/port]

 

Switch# show cdp neighbors [type module/port] [detail]

 

Enable and browse CDP information on a CLI- based switch :

 

Switch(enable) set cdp {enable|disable} module/port

 

In order to view the CDP notification information of Cisco neighboring devices :

 

Switch(enable) show cdp neighbors[module/port] [vlan|duplex|capabilities|detail]

 

5. Port Description IOS based switch:

 

Switch(config-if)# description description-string

 

CLI-based switch port description:

 

Switch(enable)set port name module/number description-string

 

6. Set the port speed on the IOS- based switch :

 

Switch(config-if)# speed{10|100|auto}

 

Set the port speed on a CLI- based switch :

 

Switch(enable) set port speed moudle/number {10|100|auto}

 

Switch(enable) set port speed moudle/number {4|16|auto}

 

7. Set the Ethernet link mode on the IOS- based switch :

 

Switch(config-if)# duplex {auto|full|half}

 

Set the link mode of the Ethernet on the CLI- based switch :

 

Switch(enable) set port duplex module/number {full|half}

 

8. Configure a static VLAN on an IOS- based switch :

 

Switch# vlan database

 

Switch(vlan)# vlan vlan-num name vla

 

Switch(vlan)# exit

 

Switch# configure teriminal

 

Switch(config)# interface interface module/number

 

Switch(config-if)# switchport mode access

 

Switch(config-if)# switchport access vlan vlan-num

 

Switch(config-if)# end

 

Configure a static VLAN on a CLI- based switch :

 

Switch(enable) set vlan vlan-num [name name]

 

Switch(enable) set vlan vlan-num mod-num/port-list

 

9. Configure VLAN trunks on IOS- based switches :

 

Switch(config)# interface interface mod/port

 

Switch(config-if)# switchport mode trunk

 

Switch(config-if)# switchport trunk encapsulation {isl|dotlq}

 

Switch(config-if)# switchport trunk allowed vlan remove vlan-list

 

Switch(config-if)# switchport trunk allowed vlan add vlan-list

 

Configure VLAN trunks on CLI- based switches :

 

Switch(enable) set trunk module/port [on|off|desirable|auto|nonegotiate]

 

Vlan-range [isl|dotlq|dotl0|lane|negotiate]

 

10. Configure the VTP management domain on the IOS- based switch :

 

Switch# vlan database

 

Switch(vlan)# vtp domain domain-name

 

Configure the VTP management domain on the CLI- based switch :

 

Switch(enable) set vtp [domain domain-name]

 

11. Configure VTP mode on the IOS- based switch :

 

Switch# vlan database

 

Switch(vlan)# vtp domain domain-name

 

Switch(vlan)# vtp {sever|cilent|transparent}

 

Switch(vlan)# vtp password password

 

Configure VTP mode on the CLI- based switch :

 

Switch(enable) set vtp [domain domain-name] [mode{ sever|cilent|transparent }][password password]

 

12. Configure the VTP version on the IOS- based switch :

 

Switch# vlan database

 

Switch(vlan)# vtp v2-mode

 

Configure the VTP version on the CLI- based switch :

 

Switch(enable) set vtp v2 enable

 

13. Start VTP tailoring on IOS- based switches :

 

Switch# vlan database

 

Switch(vlan)# vtp pruning

 

Start VTP tailoring on a CL I- based switch :

 

Switch(enable) set vtp pruning enable

 

14. Configure the EtherChannel on the IOS- based switch :

 

Switch(config-if)# port group group-number [distribution {source|destination}]

 

Configure the EtherChannel on the CLI- based switch :

 

Switch(enable) set port channel moudle/port-range mode{on|off|desirable|auto}

 

15. Adjust root path cost on IOS- based switches :

 

Switch(config-if)# spanning-tree [vlan vlan-list] cost cost

 

Adjust the root path cost on a CLI- based switch :

 

Switch(enable) set spantree portcost moudle/port cost

 

Switch(enable) set spantree portvlancost moudle/port [cost cost][vlan-list]

 

16. Adjust the port ID on the IOS- based switch :

 

Switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority

 

Adjust the port ID on the CLI- based switch :

 

Switch(enable) set spantree portpri {mldule/port}priority

 

Switch(enable) set spantree portvlanpri {module/port}priority [vlans]

 

17. Modify the STP clock on the IOS- based switch :

 

Switch(config)# spanning-tree [vlan vlan-list] hello-time seconds

 

Switch(config)# spanning-tree [vlan vlan-list] forward-time seconds

 

` switch(config)# spanning-tree [vlan vlan-list] max-age seconds

 

Modify the STP clock on the CLI- based switch :

 

Switch(enable) set spantree hello interval[vlan]

 

Switch(enable) set spantree fwddelay delay [vlan]

 

Switch(enable) set spantree maxage agingtiame[vlan]

 

18. Enable or disable the Port Fast feature on the IOS- based switch port :

 

Switch(config-if)#spanning-tree portfast

 

Enable or disable the Port Fast feature on the CLI- based switch port :

 

Switch(enable) set spantree portfast {module/port}{enable|disable}

 

19. Enable or disable the UplinkFast feature on the IOS- based switch port :

 

Switch(config)# spanning-tree uplinkfast [max-update-rate pkts-per-second]

 

Enable or disable the UplinkFast feature on the CLI- based switch port :

 

Switch(enable) set spantree uplinkfast {enable|disable}[rate update-rate] [all-protocols off|on]

 

20. To configure the switch as a clustered command switch , first assign an IP address to the management interface and then use the following command : switch(config)# cluster enable cluster-name

 

21. To remove a VLAN from a trunk link , use the following command :

 

Switch(enable) clear trunk module/port vlan-range

 

22. Use the show vtp domain to display the VTP parameters of the management domain .

 

23. Use show vtp statistics to display the VTP parameters of the management domain .

 

24. The command to define TrBRF on a Catalyst switch is as follows :

 

Switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp {ieee|ibm}]

 

25. The command to define TrCRF on a Catalyst switch is as follows :

 

Switch (enable) set vlan vlan-num [name name] type trcrf

 

{ring hex-ring-num|decring decimal-ring-num} parent vlan-num

 

26. After creating TrBRF VLAN, you can assign it to the switch port to an Ethernet switch, you can use the following command to assign VLAN port:

 

Switch(enable) set vlan vlan-num mod-num/port-num

 

27. The command show spantree shows the STP status of a switch port .

 

28. To configure the LES and BUS of an ELAN , you can use the following commands :

 

ATM (config)# interface atm number.subint multioint

 

ATM(config-subif)# lane serber-bus ethernet elan-name

 

29. Configure LECS:

 

ATM(config)# lane database database-name

 

ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address

 

ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address

 

ATM(lane-config-databade)# name ...

 

30. After creating the database , you must start the LECS. command on the main interface as follows :

 

ATM(config)# interface atm number

 

ATM(config-if)# lane config database database-name

 

ATM(config-if)# lane config auto-config-atm-address

 

31. Configure each LEC to a different ATM subinterface . The command is as follows :

 

ATM(config)# interface atm number.subint multipoint

 

ATM(config)# lane client ethernet vlan-num elan-num

 

32. Use the show lane server to display the status of the LES .

 

33. Use the show lane bus to display the status of the bus .

 

34. Use show lane database to display the LECS database content .

 

35. Use the show lane client to display the status of the LEC .

 

36. Use the show module to display a list of installed modules .

 

37. Establish a connection to the VLAN using the physical interface :

 

Router# configure terminal

 

Router(config)# interface media module/port

 

Router(config-if)# description description-string

 

Router(config-if)# ip address ip-addr subnet-mask

 

Router(config-if)# no shutdown

 

38. Use a trunk link to establish a connection to the VLAN :

 

Router(config)# interface module/port.subinterface

 

Router(config-ig)# encapsulation[isl|dotlq] vlan-number

 

Router(config-if)# ip address ip-address subnet-mask

 

39. Use LANE to establish a connection to the VLAN :

 

Router(config)# interface atm module/port

 

Router(config-if)# no ip address

 

Router(config-if)# atm pvc 1 0 5 qsaal

 

Router(config-if)# atm pvc 2 0 16 ilni

 

Router(config-if)# interface atm module/port.subinterface multipoint

 

Router(config-if)# ip address ip-address subnet-mask

 

Router(config-if)# lane client ethernet elan-num

 

Router(config-if)# interface atm module/port.subinterface multipoint

 

Router(config-if)# ip address ip-address subnet-name

 

Router(config-if)# lane client ethernet elan-name

 

Router(config-if)# ...

40. In order to perform dynamic routing configuration on the routing processor , the following IOS commands can be used :

 

Router(config)# ip routing

 

Router(config)# router ip-routing-protocol

 

Router(config-router)# network ip-network-number

 

Router(config-router)# network ip-network-number

 

41. Configure the default route :

 

Switch(enable) set ip route default gateway

 

42. Assign a VLANID to a route processor , using the following commands in interface mode :

 

Router(config)# interface interface number

 

Router(config-if)# mls rp vlan-id vlan-id-num

 

43. Enable MLSP on the route processor :

 

Router(config)# mls rp ip

 

44. In order to place an external route processor interface and switch in the same VTP domain :

 

Router(config)# interface interface number

 

Router(config-if)# mls rp vtp-domain domain-name

 

45. View information about the specified VTP domain :

 

Router# show mls rp vtp-domain vtp domain name

 

46. To determine the RSM or management interface on the router, the following command can be entered at the interface mode:

 

Router(config-if)#mls rp management-interface

 

47. To verify the configuration of the MLS-RP :

 

Router# show mls rp

 

48. Verify the MLS configuration on a specific interface :

 

Router# show mls rp interface interface number

 

49. In order to set the flow mask on the MLS-SE and do not want to set the access list on any of the route processor interfaces:

 

Set mls flow [destination|destination-source|full]

 

50. To make the MLS and input access list compatible, you can use the following commands in global mode:

 

Router(config)# mls rp ip input-acl

More you may be interested:

 

[Exclusive] Wireshark usage and filtering rules

 

CCIE experts tell you how to pass the CCIE lab exam in three months

 

Information about CISCO CERTIFICATION EXAM latest dumps this week